Icom Programming Software for IC-F60

Discussion on Icom technologies, including programming, tutorials, schematics, requests for help and new releases etc
Forum rules
***NOTE*** This forum and its content are not endorsed in any way by the vendor and users are advised to exercise caution when viewing and/or acting on any information contained within. We accept no responsibility for your devices and strongly warn you to check your warranty conditions and seek expert advice before proceeding.
Post Reply
action
Registered User
Posts: 4
Joined: Mon Jan 24, 2011 12:15 pm

Icom Programming Software for IC-F60

Post by action »

Hi can someone please help me with finding the software? Using Windows 7

User avatar
Phantom
Forum Manager
Posts: 1305
Joined: Thu May 15, 2008 12:28 pm
Location: SE QLD

Icom Programming Software for IC-F60

Post by Phantom »

Welcome to the forum

Maybe introduce yourself and tell us where your from. That would be a nicer 1st post

As for the software??

User avatar
Stretch
Registered User
Posts: 3527
Joined: Thu Aug 09, 2007 8:29 pm
Location: Gold Coast
Contact:

Re: Icom Programming Software for IC-F60

Post by Stretch »

orangepeel wrote:Maybe introduce yourself and tell us where your from. That would be a nicer 1st post
Try introducing yourself here.
Mitch Rogers

User avatar
rochedalescan
Founder
Posts: 1631
Joined: Fri Jun 01, 2007 5:08 pm
Location: Brisbane
Contact:

Re: Icom Programming Software for IC-F60

Post by rochedalescan »

Welcome...

I don't think you will find programming software that will be compatable with windows 7 If no one else is able to help you I know that http://www.uhfworld.com/ has the software available but you will have to pay the joining fee of 10$ I think it is anually.

Regards Shane
Shane Logan
Aussiescanners Founder

Australia's Premier Communications forum!
~ Please contact Phil for administration enquiries ~

alinco21
Senior Member
Posts: 699
Joined: Sat Jun 02, 2007 5:27 pm
Location: Earth around the Gold Coast Area.

Re: Icom Programming Software for IC-F60

Post by alinco21 »

yes win 7 is not very radio friendly, try in the compatibilty section run the program as XP and then give it a go. Not sure about the Icom stuff but the Yaseu software works fine.
Last edited by alinco21 on Tue Jan 25, 2011 3:54 am, edited 1 time in total.

action
Registered User
Posts: 4
Joined: Mon Jan 24, 2011 12:15 pm

Re: Icom Programming Software for IC-F60

Post by action »

Thanks guys for your help its much appreciated :D

Wuffybehr
Registered User
Posts: 4
Joined: Mon Feb 07, 2011 8:46 am

Re: Icom Programming Software for IC-F60

Post by Wuffybehr »

you may want to try compatibility mode if you can

User avatar
Phil
Administrator
Posts: 1500
Joined: Sun Jun 03, 2007 8:51 pm
Location: Southside of Brisbane, Qld

Re: Icom Programming Software for IC-F60

Post by Phil »

Just a note guys so you don't have to waste your energy the ICOM IC-F50/60 it programming software is the CS-F50 which is on the forums from memory if not send me a pm and i can see what i can do
Phil
Forum Administrator
phil@aussiescanners.com.au

Uniden UBCD996T, RH96
Motorola GP328, GP338, GP328 Plus, XTS3000, GM300, DP3400 VHF x2, DP4801e, DP4801ex, DM4601e, XTL5000-03, XTS2500 M3
Simoco SRM9030 AC, SRM9022 UW
Hytera - PD412, PD462, PD682, MD782G, PD782G
Icom IC-F60, IC-410 Pro
Tait TM8250
Kenwood - NX720HG

Stoney
Registered User
Posts: 4
Joined: Wed Mar 30, 2011 7:21 pm

Re: Icom Programming Software for IC-F60

Post by Stoney »

Hi there,

CS-F50 works fine, but not tried with Windows 7. I have an old comp. down there for such thinks.

Post Reply